#Factory resetting an iei keypad serial#
#Factory resetting an iei keypad code#

#Factory resetting an iei keypad serial#

The XR100/500 Series can update firmware with network or serial.*Note: Serial connections MUST be done on the J22 header or J21 DB9 connecter with the J23 jumper set to R. XR100/500: The XR100/500 can be connected and programmed via network, dialer, cell, and serial. In Remote Link, set the connection type to Direct with a baud rate of 38400 when updating the XT Series panels. A 399 cable or 401 module can be used to directly update the panel firmware. XT30/50, XTL, XTLplus and XTLtouch: The XT and XTL Series panels can only be connected and programmed via network, cell, or dialer on XT30/50D. Don’t forget to program the device number that you set your keypad to in Device Setup of panel programming to make sure the keypad will be operational when you change the address. Select the existing setting to clear out the current address and enter in the new address. Select OPT and the current keypad address will be displayed. The first screen to appear is KPD OPT, KPD DIAG, KPD STOP.

#Factory resetting an iei keypad code#

On the next screen, tap on the wrench and enter code 3-5-7-7 (I-N-S-T) CMD to enter installer options. Don’t forget to program the device number in Device Setup panel programming to make sure the keypad will be operational when you change the address.For 7800 or 9800 Series keypads, scroll the keypad carousel until you see OPTIONS and select it. To change the address, press any of the top row keys to clear out the existing setting and then insert the desired keypad address. Select OPT and the screen will then show the current keypad address, which is 1 by default. If the LED turns on for more than one second, or if the LED is flashing multiple times, relocate the wireless transmitter or receiver until the transmitter is consistently showing the LED turning on for less than a second each time the tamper is pressed.įor the 7000 Series keypads, simply press and hold the back arrow and CMD at the same time until the keypad shows 'SET BRIGHTNESS.' When that appears on the screen, press 3-5-7-7 (I-N-S-T) CMD to enter installer options. DMP recommends repeating this test several times to confirm reliable communication. Each wireless transmitter has a red LED built-in that provides visual confirmation that the transmitter, the LED should quickly blink one time when pressing the tamper and one time when releasing the tamper. The other option is the transmitter survey LED operation that is built into all 1100 Series wireless products. This can also be done in Dealer Admin under System Tests -> Wireless Test.

When the test ends, the screen will also display which transmitters failed, if any. The panel will show the status on the screen of how many transmitters are checking in. Zones that fail either need to be relocated or a repeater should be added. By pressing the WLS option on the screen this will begin a wireless check-in test that will run for five minutes and check the consistency of your signals. Press CMD until the WLS option is displayed, and select it. Then, at a keypad, press 8-1-4-4 (W-A-L-K) (then press CMD on XR panels). Reset the control panel by shorting the RESET header or pressing the RESET button, depending on the panel. The first option is the wireless test, in which the panel directs each transmitter that is currently programmed to check in. There are two ways to test DMP wireless communication: Select KPD OPT to enter the keypad options menu. Tap the wrench icon and the keypad will display 'ENTER CODE'- press 3-5-7-7 (I-N-S-T) CMD and that will show KPD OPT, KPD DIAG, and STOP. When the Options icon is pressed the keypad will display settings for brightness, tone, and volume. Keypad Options: To gain access to the keypad options on the 7800 Graphic Touchscreen Keypad, scroll through the carousel on the keypad until 'Options' is displayed and select it.

The keypad screen will display DIAGNOSTICS. *XR series panels need 6-6-5-3+CMDĭiagnostics: To access diagnostics on DMP control panels, reset the control panel by momentarily placing a jumper on J16 and then remove it where it’s only placed on one pin. If the keypad says 'ENTER CODE' after pressing P-R-O-G, enter the lockout code that was programmed by the original installing company. Programming: To access panel programming on DMP control panels, reset the control panel by shorting the RESET header or pressing the RESET button depending on the panel.